---
title: "EMLA Encoder Error Guide"
url: "https://support.sardius.media/knowledge-base/understanding-emla-error-codes"
category: "Sardius EMLA Encoder"
updated: 2026-08-20
summary: "Some EMLA Encoder Errors may need some additional context to resolve."
---

# EMLA Encoder Error Guide

Some EMLA Encoder Errors may need some additional context to resolve. 

### **Error States**

- **Warning** - A non-critical message. Your stream is likely not negatively affected.
- **Set** - Critical Alarm that needs immediate address. 
- **Active** - New Critical Alarm. Please wait for additional information.
- **Cleared** - This error has been resolved. Messages that are "Cleared" will disappear within 10 minutes of entering this state.

### **Channel Error Messages**

#### _MediaLive reports active alert(s)_

- _Reason_: a channel is experiencing an issue. 
- **Action:** Locate the channel having the issue and view the alerts there.

#### _No input timecodes detected_

- This is a Warning message, your stream is likely stable.
- _Reason_: Your template is set to reference timecode in the input stream, but no timecode is present. For muxed streams, this will be a non-issue, but unmuxed streams could experience a/v sync drift.
- **Action**: Adjust your template to use Zero-based or System clock timecode for the next stream.

#### _Audio loudness is out of range. Check audio source._

- This is a Warning message, your stream is likely stable.
- _Reason_: Your source audio is operating outside of -24 LKFS loudness standards. This is a non-issue unless you are sending SRT to a TV network or distributor needing to adhere to LKFS standards.
- **Action**: Check LKFS monitoring in the video signal before arriving at the encoder and adjust accordingly.

#### _Input Probe is Taking Longer than Expected_

- _Reason_: The encoder was not able to detect an audio/video source on your input when the stream started. 
- **Action:** Check your SDI input to validate it is connected, and check the cable for an active signal.

#### _Video not found_

- _Reason_: The input can not detect video on your input.
- **Action:** Check your SDI input to validate it is connected, and check the cable for an active signal.

#### _Audio not found_

- _Reason_: The input can not detect audio on your input.
- **Action:** Check your SDI input to validate it is connected, and check the cable for an active signal.

#### _Muxer is taking a long time to connect to server_

- _Reason_: The stream key or credentials for your destination are invalid, and your destination is rejecting them.
- **Action:** Stop your stream. Obtain a new stream key/credentials from your destination, or check your information and re-enter. Start a new stream.

#### _Output delivery failure_

- _Reason_: The EMLA Encoder cannot reach your destination.
- **Action:** Check your network connection, and check your destination to ensure that it is still online and operational. Make adjustments where needed.

#### _ReliableTS Output not connected_

- _Reason_: The EMLA Encoder is unable to connect to the SRT destination. 
- **Action:** Stop the stream. Check and verify your SRT address, port, passphrase and stream ID (if applicable). Make adjustments where needed and restart the stream.

#### _Channel is inactive_

- _Reason_: Your streaming channel is either starting or ending.
- **Action:** No action is needed. If your channel doesn't start or disappear within 2 minutes, please contact Sardius Support.

### **Cluster Error Messages**

#### _The OS and BIOS settings for SMPTE 2110 are invalid._

- _Reason_: Your EMLA Encoder is SMPTE-2110 capable, but is not properly configured for SMPTE-2110 inputs.
- **Action:** If you are not using SMPTE-2110 inputs, no action is needed. If you would like to clear this error, contact Sardius Support for additional guidance.

#### _The node is offline_

- _Reason_: Your EMLA Encoder is either offline or has not established communication with the AWS service. 
- **Action:** Make sure your encoder is powered, and the network cable is firmly connected to the network port indicated on your encoder's Quick Start Guide.
