---
title: "Pair a Makito X4 Encoder"
url: "https://support.sardius.media/knowledge-base/pair-a-makito-x4-encoder"
category: "Makito Encoder"
updated: 2026-08-20
summary: "Learn how to pair a Makito X4 Encoder with the Sardius Control Panel."
---

# Pair a Makito X4 Encoder

> **Tip:** _This article will guide you through pairing a Makito X4 Encoder. For the Makito X Encoder, [click here](https://support.sardius.media/knowledge-base/pair-a-makito-encoder)._

Before powering up the Makito for the **first time**, please do the following:

1. Unbox the Makito and place it in your production rack (or location where it will be used)
2. Connect an SDI video signal to the Makito
3. Connect a Network cable into the "Network" port
4. Verify that the unit is at room temperature
5. **DO THIS LAST!** Plug in the power cable. The Makito will automatically begin to power up.

To configure the Makito, you will need:

- A computer that is on the same network and subnet as the Makito in order to access the Makito UI.
- A separate window/tab on that same computer that is logged into the Sardius Control Panel.

Information on how to access the Makito's UI and other startup recommendations are available by clicking here: [**https://doc.haivision.com/MakitoX4Enc1.6.1/makito-x4-encoder-quick-start-guide/access-the-web-interface**](https://doc.haivision.com/MakitoX4Enc1.6.1/makito-x4-encoder-quick-start-guide/access-the-web-interface)

> **Note:** _**Note:**_ Prior to pairing your Makito with Sardius, please contact Sardius Support to make sure your channel(s) are configured for using a Makito.

**Video**

> **Transcript:** In this video, we will show you how to pair your Makito X4 Encoder to your account. Before you begin, make sure you have two tabs open. One for the Sardius Control Panel and the other for your X4 Encoder. To begin, select Devices from the Sidebar. Next, click on Add Device in the upper right corner. A variety of encoders can be paired with our system. The Makito X4 is a Haivision encoder, so we will select Haivision to continue. The modal will ask you to sign in to your X4. If you haven't already done so, please do so now. Click Next. Now we will need to copy the pairing code. This will copy the code to the clipboard. Now we need to go to our Makito X4 Encoder. Switch to that tab and do not close the tab for the Sardius Control Panel. In the Makito, click Settings on the Sidebar. This new page has a submenu under the header. Locate Services and click on it. Look for the EMS toggle Switch. Make sure that it is selected. Then locate the EMS section. It will have a long text field and three smaller ones beneath it. In the long field, paste the passcode you obtained from the Sardius Control Panel. Click Pair. Allow this process to complete. Once it does, it will show that it is connected to the management service. If it does not connect, your X4 likely needs a DNS entry to continue. Please review our knowledge base on how to resolve that. Once you are connected, switch back to the tab with the Sardius Control Panel. Click Check for Device. This process can take up to 60 seconds, so please do not navigate away, close the tab, or refresh. When the process is complete, your encoder will be displayed on the screen. Your encoder may have an interesting name. If you would like to change that, simply click on the name of the encoder, enter in a new name and click the checkmark. Congratulations! Your Makito X4 encoder is now paired to your account! To learn more about managing your Makito X4 encoder, or using it to stream, please visit our Knowledge Base. Thank you for watching, and we will see you in the next video.

### **Walkthrough**  

1\.  Log into your Sardius Control Panel

2\. To pair an encoder, click the category titled Devices. This can be found just below the halfway point on the black, left sidebar. 

![makitoPair1](https://support.sardius.media/kb-media/89b6b465060e66ee.png)

3\. To pair a device, click the blue button that says + Add Device. This is found in the top right corner of the window at all times. If no device is currently paired (as in the photo above), the center of the screen will also have this button prominently displayed.

4\. Select Haivision as the Encoder type.

![makitoX4select](https://support.sardius.media/kb-media/f44bb7ddc56baf9f.png)

5\.  Sign into your Haivision Makito encoder.

![makitoPair2](https://support.sardius.media/kb-media/86062ab2558e87c9.png)

6\. Once inside your Makito X4 device, click Settings on the sidebar to access the inner workings (see picture below).

![makitoX4settingsSelect](https://support.sardius.media/kb-media/53f3167d0141ff81.png)

7\. Return to the Sardius Control Panel. Within the Device setup modal, click the button that says Copy pairing code

![makitoX4pairingCode](https://support.sardius.media/kb-media/329b0b30994c0831.png)

8\. Back in the Makito Administration screen, click Services from the top menu, then locate the toggle for EMS. Make sure it is selected, then scroll down the EMS section. 

![makitoX4services](https://support.sardius.media/kb-media/05d2e6aca21af4af.png)

9\. Paste the pairing code into the box labeled "Passcode" then click "Pair."

![makitoX4insertCode](https://support.sardius.media/kb-media/c993fca03d99431d.png)

> **Tip:** _**Helpful Tip:**_ If the encoder is still paired to a previous service, the Pair button will say _Unpair._ Please make sure the encoder is unpaired prior to pairing to Sardius Control Panel.

10\. In the Sardius Control Panel, finish the pairing by clicking the button in the bottom right of the modal: Check for Device

![makitoX4checkForDevice](https://support.sardius.media/kb-media/2960461f31317b94.png)

Congratulations! Your Makito has been successfully paired to your account.
